One signal has no output
1. Whether the parameters of the carving machine and the computer settings are correct. Is the signal line connected correctly?
Second, the carving data presents an unclean condition
1. The tool is blunt, there must be wear and tear, and the demand is grinding.
2. Whether the tool setting in the software matches the practical tool
3. Whether to increase the lubricant when carving hard materials (such as metal, jade, glass, etc.)
4. Whether the arbor is concentric
The three heads cannot be returned to zero and the engraving machine is reduced or out of bounds.
1. The machine head cannot be returned to the zero position, the lead screw may be misaligned, and the lead screw needs to be adjusted.
2. Travel switch damage
3. The machine can not be returned to zero and the size of the engraving machine is reduced or out of bounds. It may be that the "model" in the machine setting does not match the actual model.
Four running knife
1. The ground wire is not installed, showing static electricity, causing running knife and dislocation
2. The printer parameters in the software do not match the engraving machine print parameters.
Five often cut the knife when cutting hard materials
1. When carving hard materials, you need to set different carving parameters and use different tools according to different materials.
2. Pick the right lubricant
Six 琢 琢 machine start to reset when beeping or always good top bad limit switch
1. The top of the jack is less than the limit switch, and it can be corrected.
2, the drive line contact is not good, try to fix the drive line.
3. The limit switch line is not connected, and the line can be connected.
4, the limit switch is broken, you can change it.
Seven carving machine can not be carved at the origin
1. Whether the layout size of the file matches the machine.
2. Check if the offset (OFFSET) is set and the layout is correct.
The spindle motor suddenly stops or slows down during the operation of the carving machine.
1. The operating voltage is unstable or overloaded, and a voltage regulator can be added.
2. Check if the middle line is connected and whether the line is de-welded.
Nine When the original setting is set, the distance between the forward and the right is sometimes uncertain?
1. The limit switch fails. When the system returns to the original point of the system, the limit switch is closed and popped open. Change the limit switch.
2. The drive line is loose. Try to fix it tight.
When the sculpt machine is reset, the X-axis, Y-axis, and Z-axis can be indeterminate.
1. The limit switch is broken (the limit switch is always closed), and it can be replaced.
2. The drive line is broken (X-axis 14-pin and 15-pin short-circuit, Y-axis 13-pin and 15-pin short-circuit, Z-axis 31-pin and 15-pin short-circuit), change the drive line or separate the short circuit.
3. The drive board is broken and the drive board can be changed.
十一 The motor does not work after starting up
1. There is no output or incorrect setting of the variable frequency power supply. / View the three-phase output voltage and setting method of the variable frequency power supply.
2. The motor plug is not plugged in. Check the motor plug and connection.
3, the plug connection is not good
4, the stator wire package is broken / replacement line package
12 After a few seconds of operation, stop working after a few seconds.
1, the motor inlet line package insulation is not good / drying line package
2. Damage to the wire package insulation caused by high temperature of the motor / replacement of the line package
3, the motor phase loss operation causes overcurrent and protects the power outage / view the motor connection
4, the starting time is too short / extended to speed up the moment
Thirteen seconds after the start-up, the motor smokes or the casing is hot.
1. The output voltage and frequency of the inverter do not match the voltage and frequency of the motor. Check the voltage and frequency of the inverter and the motor.
2, the inverter setting is incorrect / reset the inverter
Fourteen tighten the nut when starting
1. The direction of rotation is wrong / change the direction of rotation
